decimal3d:userguide:tutorials:all_tutorials
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
decimal3d:userguide:tutorials:all_tutorials [2023/01/19 21:45] – [Software Settings] kerhart | decimal3d:userguide:tutorials:all_tutorials [2023/01/20 13:06] (current) – dpatenaude | ||
---|---|---|---|
Line 31: | Line 31: | ||
The decimal3D Software Settings allow the user to configure the following items: | The decimal3D Software Settings allow the user to configure the following items: | ||
- | * [[decimal3d: | + | * [[decimal3d: |
* [[decimal3d: | * [[decimal3d: | ||
* [[decimal3d: | * [[decimal3d: | ||
Line 38: | Line 38: | ||
- | ==== DICOM Export | + | ==== DICOM Plan Export ==== |
- | <WRAP center round important | + | <WRAP center round important |
**Notes: | **Notes: | ||
- | - Prior to setting up this option, ensure with your IT team that the iPad has been granted network access to this DICOM server. | + | - Prior to setting up this option, ensure with your IT team that the iPad has been granted network access to your DICOM server |
- When prompted by the iPad, please ensure to select the option to allow decimal3D to find and connect to devices on your local network. | - When prompted by the iPad, please ensure to select the option to allow decimal3D to find and connect to devices on your local network. | ||
</ | </ | ||
- | Setting up a DICOM export | + | Setting up a DICOM export |
* **DICOM Receiver Hostname**: The IP address (e.g.: 192.168.12.7) or resolvable network hostname (e.g.: the server name) of the DICOM server intended to export to. | * **DICOM Receiver Hostname**: The IP address (e.g.: 192.168.12.7) or resolvable network hostname (e.g.: the server name) of the DICOM server intended to export to. | ||
* **DICOM Receiver Port**: The TCP/IP port of the DICOM monitoring/ | * **DICOM Receiver Port**: The TCP/IP port of the DICOM monitoring/ | ||
Line 55: | Line 55: | ||
* None: This will omit the applicator from the DICOM RT Plan during export. | * None: This will omit the applicator from the DICOM RT Plan during export. | ||
- | Below are the steps required to setup a DICOM Export | + | Below are the steps required to setup a DICOM Export |
- | - Obtain the IP Address and Port used for existing | + | - Obtain the IP Address and Port used for the desired destination (DICOM Receiver). |
- | - | + | - Enter the IP Address and Port in the decimal3D Advanced Settings page. |
+ | - Run the DICOM Receiver ECHO test on the Advanced Settings page. | ||
+ | - If successful, set up is complete and export is ready. | ||
+ | - If unsuccessful, | ||
+ | <WRAP center round important 70%> | ||
+ | **Notes: | ||
+ | - The option to export a DICOM Plan file is only enabled once the block has been ordered. | ||
+ | - The electron block present in the exported DICOM RT Plan file will not include any millability features (e.g.: the rounding of sharp corners to simulate fabrication) that decimal3D applied to your devices. | ||
+ | </ | ||
- | **Note: the electron block present in the exported DICOM RT Plan file will not include any millability features (e.g.: the rounding of sharp corners to facilitate in fabrication) that decimal3D applied to your devices.** | ||
- | === Troubleshooting DICOM Export | + | === Troubleshooting DICOM Export === |
If your DICOM Export ECHO Test fails, it may be due to the following reasons. Note: .decimal may not be able to assist with most of these issues, as it is dependent on your IT network security policies. | If your DICOM Export ECHO Test fails, it may be due to the following reasons. Note: .decimal may not be able to assist with most of these issues, as it is dependent on your IT network security policies. | ||
Line 70: | Line 77: | ||
| Different WiFi | Some hospitals set up their iPad on a WiFi network (e.g.: a guest WiFi network) that is siloed off and does not permit access to the DICOM server. Please contact your IT team to ensure the iPad is on the same network as your DICOM server and that the iPad is allowed to transmit data to the DICOM server/ | | Different WiFi | Some hospitals set up their iPad on a WiFi network (e.g.: a guest WiFi network) that is siloed off and does not permit access to the DICOM server. Please contact your IT team to ensure the iPad is on the same network as your DICOM server and that the iPad is allowed to transmit data to the DICOM server/ | ||
| Local Network Access | Ensure the decimal3D application has been granted network access on the iPad: Open the Settings app, scroll down and select the decimal3D application. Ensure the setting 'Local Network' | | Local Network Access | Ensure the decimal3D application has been granted network access on the iPad: Open the Settings app, scroll down and select the decimal3D application. Ensure the setting 'Local Network' | ||
- | | Eclipse | + | | DICOM Receiver |
==== Download Activity Logs ==== | ==== Download Activity Logs ==== | ||
Line 80: | Line 87: | ||
This option allows the user to set whether they want to include the patient MRN in the order file's PO field that is set to .decimal. This option allows some centers to easily link an order placed to .decimal to the patient record based on the patient' | This option allows the user to set whether they want to include the patient MRN in the order file's PO field that is set to .decimal. This option allows some centers to easily link an order placed to .decimal to the patient record based on the patient' | ||
- | **Note: The MRN is considered by some hospital' | + | **Note: The MRN is considered by some hospital' |
decimal3d/userguide/tutorials/all_tutorials.txt · Last modified: 2023/01/20 13:06 by dpatenaude