decimal3d:userguide:tutorials:all_tutorials
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
decimal3d:userguide:tutorials:all_tutorials [2023/01/19 22:17] – [Troubleshooting DICOM Export Servers] kerhart | decimal3d:userguide:tutorials:all_tutorials [2023/01/19 22:29] – kerhart | ||
---|---|---|---|
Line 31: | Line 31: | ||
The decimal3D Software Settings allow the user to configure the following items: | The decimal3D Software Settings allow the user to configure the following items: | ||
- | * [[decimal3d: | + | * [[decimal3d: |
* [[decimal3d: | * [[decimal3d: | ||
* [[decimal3d: | * [[decimal3d: | ||
Line 38: | Line 38: | ||
- | ==== DICOM Export | + | ==== DICOM Plan Export ==== |
- | <WRAP center round important | + | <WRAP center round important |
**Notes: | **Notes: | ||
- Prior to setting up this option, ensure with your IT team that the iPad has been granted network access to this DICOM server. | - Prior to setting up this option, ensure with your IT team that the iPad has been granted network access to this DICOM server. | ||
Line 46: | Line 46: | ||
</ | </ | ||
- | Setting up a DICOM export | + | Setting up a DICOM export |
* **DICOM Receiver Hostname**: The IP address (e.g.: 192.168.12.7) or resolvable network hostname (e.g.: the server name) of the DICOM server intended to export to. | * **DICOM Receiver Hostname**: The IP address (e.g.: 192.168.12.7) or resolvable network hostname (e.g.: the server name) of the DICOM server intended to export to. | ||
* **DICOM Receiver Port**: The TCP/IP port of the DICOM monitoring/ | * **DICOM Receiver Port**: The TCP/IP port of the DICOM monitoring/ | ||
Line 55: | Line 55: | ||
* None: This will omit the applicator from the DICOM RT Plan during export. | * None: This will omit the applicator from the DICOM RT Plan during export. | ||
- | Below are the steps required to setup a DICOM Export | + | Below are the steps required to setup a DICOM Export |
- | - Obtain the IP Address and Port used for existing | + | - Obtain the IP Address and Port used for the desired destination (DICOM Receiver). |
- | - | + | - Enter the IP Address and Port in the decimal3D Advanced Settings page. |
+ | - Run the DICOM Receiver ECHO test on the Advanced Settings page. | ||
+ | - If successful, set up is complete and export is ready. | ||
+ | - If unsuccessful, | ||
+ | <WRAP center round important 70%> | ||
+ | **Notes: | ||
+ | - The option to export a DICOM Plan file is only enabled once the block has been ordered. | ||
+ | - The electron block present in the exported DICOM RT Plan file will not include any millability features (e.g.: the rounding of sharp corners to simulate fabrication) that decimal3D applied to your devices. | ||
+ | </ | ||
- | **Note: the electron block present in the exported DICOM RT Plan file will not include any millability features (e.g.: the rounding of sharp corners to facilitate in fabrication) that decimal3D applied to your devices.** | ||
=== Troubleshooting DICOM Export Servers === | === Troubleshooting DICOM Export Servers === | ||
Line 80: | Line 87: | ||
This option allows the user to set whether they want to include the patient MRN in the order file's PO field that is set to .decimal. This option allows some centers to easily link an order placed to .decimal to the patient record based on the patient' | This option allows the user to set whether they want to include the patient MRN in the order file's PO field that is set to .decimal. This option allows some centers to easily link an order placed to .decimal to the patient record based on the patient' | ||
- | **Note: The MRN is considered by some hospital' | + | **Note: The MRN is considered by some hospital' |
decimal3d/userguide/tutorials/all_tutorials.txt · Last modified: 2023/01/20 13:06 by dpatenaude