Differences

This shows you the differences between two versions of the page.

--- decimal3d:userguide:tutorials:all_tutorials [2023/01/19 22:18] – [MRN to PO Field] kerhart
+++ decimal3d:userguide:tutorials:all_tutorials [2023/01/20 13:06] (current) – dpatenaude
@@ Line 31: / Line 31: @@
 The decimal3D Software Settings allow the user to configure the following items:
-  * [[decimal3d:userguide:tutorials:all_tutorials#dicom_export_servers|DICOM Export Servers]]
+  * [[decimal3d:userguide:tutorials:all_tutorials#dicom_plan_export|DICOM Plan Export]]
   * [[decimal3d:userguide:tutorials:all_tutorials#download_activity_logs|Download activity/usage logs]]
   * [[decimal3d:userguide:tutorials:all_tutorials#mrn_to_po_field|Set MRN to PO Field]]
@@ Line 38: / Line 38: @@
-==== DICOM Export Servers ====
+==== DICOM Plan Export ====
-<WRAP center round important 60%>
+<WRAP center round important 70%>
 **Notes:**\\
-  - Prior to setting up this option, ensure with your IT team that the iPad has been granted network access to this DICOM server.
+  - Prior to setting up this option, ensure with your IT team that the iPad has been granted network access to your DICOM server from the iPad.
   - When prompted by the iPad, please ensure to select the option to allow decimal3D to find and connect to devices on your local network.
 </WRAP>
-Setting up a DICOM export server allows users to export an RT Plan with the design device. The following options are present in the DICOM Export Server settings:
+Setting up a DICOM export filter (sender) allows users to export an RT Plan with the design device. The following options are present in the DICOM Export settings:
   * **DICOM Receiver Hostname**: The IP address (e.g.: 192.168.12.7) or resolvable network hostname (e.g.: the server name) of the DICOM server intended to export to.
   * **DICOM Receiver Port**: The TCP/IP port of the DICOM monitoring/listening receiver (e.g.: 104)
@@ Line 55: / Line 55: @@
     * None: This will omit the applicator from the DICOM RT Plan during export.
-Below are the steps required to setup a DICOM Export Server:
+Below are the steps required to setup a DICOM Export Filter (sender):
-  - Obtain the IP Address and Port used for existing DICOM Receiver.
+  - Obtain the IP Address and Port used for the desired destination (DICOM Receiver).
-    -
+  - Enter the IP Address and Port in the decimal3D Advanced Settings page.
+  - Run the DICOM Receiver ECHO test on the Advanced Settings page.
+  - If successful, set up is complete and export is ready.
+  - If unsuccessful, refer to the troubleshooting items below for further guidance.
+<WRAP center round important 70%>
+**Notes:**\\
+  - The option to export a DICOM Plan file is only enabled once the block has been ordered.
+  - The electron block present in the exported DICOM RT Plan file will not include any millability features (e.g.: the rounding of sharp corners to simulate fabrication) that decimal3D applied to your devices.
+</WRAP>
-**Note: the electron block present in the exported DICOM RT Plan file will not include any millability features (e.g.: the rounding of sharp corners to facilitate in fabrication) that decimal3D applied to your devices.**
-=== Troubleshooting DICOM Export Servers ===
+=== Troubleshooting DICOM Export ===
 If your DICOM Export ECHO Test fails, it may be due to the following reasons. Note: .decimal may not be able to assist with most of these issues, as it is dependent on your IT network security policies.